Freelancers using ProteusFreelancers using Proteus
ProjectsPeople
Adeagbo AbdulJeleel's avatar
Adeagbo AbdulJeleel
Lagos, Nigeria
Designing PCBs, electronics, embedded and product design
New to Contra
Designing PCBs, electronics, embedded and product design
Cover image for Raspberry Pi CM5 Carrier Board
Raspberry Pi CM5 Carrier Board with Class-D Amp In this design, Texas Instruments TPA3118 Class-D amplifier is integrated on the PCB carrying Raspberry Pi CM5. Power supply is coming from USB-PD input via Type-C port. I/O ports 1 x HDMI 1 x DSI 22p FPC connector 2 x USB 3.0 Type-A 2 x USB 2.0 Type-A 1 x M.2 M-Key PCIe slot for SSD 1 x 3.5mm stereo Line-out jack 1 x USB Type-C Debug/Flash 1 x USB Type-C PD 1 x PWM Fan connector 1 x RGB LED 3-p connector connected to GPIO 1 x rotary encoder input connected to GPIO ICs Texas Instruments PCM5102A, 2.1 VRMS, 112/106/100 dB Audio Stereo DAC with PLL and 32-bit, 384 kHz PCM Interface Texas Instruments TPA3118D2, 30-W stereo, 60-W mono, 4.5- to 26-V supply, analog input Class-D audio amplifier Injoinic IP2721, TYPEC/PD2.0/PD3.0 Physical Layer IC for USB Type-C input Interfaces Terminus Tech FE1.1s, USB 2.0 High Speed 4-port Hub Controller
0
71
Cover image for Raspberry Pi Zero Relay Board I
Raspberry Pi Zero Relay Board I designed a custom Raspberry Pi Zero relay control board that combines a Raspberry Pi Zero development platform with multiple relay outputs for controlling external electrical loads. The objective of the project was to allow the Raspberry Pi Zero to electronically control the relays, providing a practical interface between the low-voltage digital signals from the Pi and connected external devices. My work involved developing the PCB layout around the Raspberry Pi Zero, organizing the relay circuitry, and carefully routing the control and power connections. Particular attention was given to component placement, signal routing, power distribution, isolation between the control circuitry and relay sections, and maintaining a clean, reliable board layout. The project provided valuable experience in Raspberry Pi hardware integration, relay control, PCB design, digital interfaces, and hardware prototyping, while demonstrating how a compact embedded platform can be integrated with a dedicated control board for real-world automation applications.
0
78
Cover image for PWM Module - Multi-Channel PCB
PWM Module - Multi-Channel PCB Design Designed a custom PCB integrating four independent PWM (Pulse Width Modulation) modules on a single board, creating a compact and practical solution for controlling multiple output channels. The PWM modules can be used for applications such as DC motor speed control, LED brightness adjustment, and light dimming. My work involved translating the circuit requirements into a functional PCB layout, carefully arranging the four PWM sections while maintaining clear separation between functional blocks. I focused on efficient component placement, clean signal routing, power distribution, grounding, and practical board organization. Combining four PWM channels onto a single PCB required careful planning to make effective use of the available board space while keeping the design organized and suitable for assembly. This project strengthened my experience in multi-channel PCB design, power and signal routing, motor control applications, and practical electronics hardware development.
0
77
Cover image for PCI Device - 8-Layer PCB
PCI Device - 8-Layer PCB Design I worked on an 8-layer PCI device PCB, carrying out detailed modifications to an existing design based on the client's specific engineering requirements. My role involved carefully reviewing the existing PCB layout, understanding the design structure and layer stack-up, and implementing the requested changes while preserving the integrity of the original design. I paid close attention to component placement, routing, power and ground distribution, layer management, and maintaining appropriate clearances throughout the board. Working with an 8-layer PCB required careful consideration of signal routing and inter-layer connections, particularly in areas where multiple signals and components were densely packed. Each modification was implemented with attention to the existing design constraints to ensure that the updated board remained practical, reliable, and suitable for manufacturing. This project strengthened my experience in high-layer-count PCB design, design modification, multilayer routing, and working within an established engineering design environment.
0
67
Proteus(5)
Muhammad Shahzaib's avatar
Muhammad Shahzaib
Karachi, Pakistan
Senior Lead Graphic Designer | UI/UX & Product Engineer
New to Contra
Senior Lead Graphic Designer | UI/UX & Product Engineer
Cover image for Wind Power Solution
Wind Power Solution
0
4
Cover image for My Introduction
My Introduction
0
41
Cover image for CongoVIP
CongoVIP
0
137
Cover image for NewGenia: : Clinical bioinformatics for clinicians
NewGenia: : Clinical bioinformatics for clinicians
1
204
Proteus(1)
Jean-Luc Maurel's avatar
Jean-Luc Maurel
Pinetown, South Africa
Systems Engineering, Technology & Designing Solutions
New to Contra
Systems Engineering, Technology & Designing Solutions
Cover image for PLC Panel Design and Configuration
PLC Panel Design and Configuration
0
38
Cover image for Hino Vin Labeler
Hino Vin Labeler
0
28
Cover image for Multi node CAN Bus network
Multi node CAN Bus network environmental monitoring
0
41
Cover image for Completed Catalytic converter scanners
Completed Catalytic converter scanners
0
41
Proteus(1)
Dian Eka Putra's avatar
Dian Eka Putra
Makassar, Indonesia
Data Analyst | Research | Excel | Automation
New to Contra
Data Analyst | Research | Excel | Automation
Cover image for Technical & Engineering
Technical & Engineering
1
55
Cover image for Research & Market Analysis
Research & Market Analysis
1
75
Cover image for Excel Data Analysis & Reporting
Excel Data Analysis & Reporting
1
92
Cover image for Web Development & Digital Solution
Web Development & Digital Solution
1
97
Proteus(1)